Schneider Electric 1.5 Kw 200/240v Ac Monophase Motor Speed Controller 3606480071096 Atv12hu15m2

SCHNEIDER ELECTRIC ATV12HU15M2 1.5 KW 200/240V AC MOTOR SPEED CONTROL DEVICE WITH 1 PHASE INPUT AND 3 PHASE OUTPUT Schneider Electric speed control devices are developed at a high quality level, including compact systems and specially designed mixed solutions, and thanks to its production quality and experience, it works with all loads. tested under conditions. There are many reasons to choose the 1.5 kW speed controller. Some of those; Time is saved in commissioning. Time is saved in programming. Time is saved in cable connection. The design is completely focused on integration. It can be programmed without removing the product’s box or powering it on. The product with reference code ATV12HU15M2 has 1.5 kW moto power. The number of digital inputs is 4, the number of digital outputs is 2. Some of the product application areas are small conveyors, small labeling machines, small bagging machines, grinders, kneading machines, mixers. Brand Schneider Full Product Code ATV12HU15M2 Series Altivar 12 Product or Component Type Variable Speed ??Drive [Ue] Nominal Operating Voltage 200…240 V – 15…10 % [Ie] Nominal Operating Current 17.8 A 200 V Product Arrival Location Asynchronous motors Component Name ATV12 Number of Phases 1 Phase Motor Power kW 1.5 kW Motor Power hp 2 hp Line Current 17.8 A at 200 V14.9 A at 240 V Speed ??Range 1…20 IP Protection Degree IP20 without cover plate on the upper part Product Series Altivar 12 Product Specific Application Simple Machine Nominal Supply Voltage 200…240 V – 15…10 % EMC Filter Integrated Supply Frequency 50/60 Hz +/- 5 % Type of Connector 1 RJ45 (front percent) for Modbus Physical Interface Modbus Transmission Frame for 2-wire RS 485 Modbus Transmission Rate for RTU 4800 bits/sec9600 bits/s19200 bits/s38400 bits/sec Number of Addresses Modbus Communication Service for 1?247 Read standby registers (03) 29 wordTek registers write (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsRead device description (43) Continuous Output Current 7.5 A at 4 kHz Maximum Transient Current 11.2 A for 60 s Speed ??Controller Output Frequency 0.5?400 Hz Braking Torque Up to 70% of the nominal motor torque without braking resistor Output Voltage 200…240 V 3 phase Electrical Connection Terminal, clamping capacity: 5.5 mm?, AWG 10 (L1 , L2, L3, U, V, W, PA, PC) Tightening Torque 1.2 Nm Insulation Electrical between power and control Supply Internal supply for reference potentiometer: 5 V DC (4.75?5.25 V), 11 V (case 1) Sampling Time 20 ms, tolerance +/- 1 ms for logic input Analog input for 10 ms Linearity Error +/- 0.3% of maximum value Analog input for Analog Output Type AO1 software-configurable voltage: 0.. .10 V, impedance: 470 Ohm, resolution 8 bitAO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bit Digital Output Type Logic output LO+, LO-Protected relay output R1A, R1B, R1C 1 K/A Minimum Switching Current 5 mA at 24 V DC for logic relay Maximum Switching Current 2 A 250 V AC inductive cos phi = 0,4 L/R = 7 msec logic relay2 A 30 V DC inductive cos phi = 0.4 L/R = 7 msec logic relay3 A 250 V AC resistive cos phi = 1 L/R = 0 msec logic relay4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay Braking to Stop With DC injection,